Rotational Motion

The value of $J$ is ____.

The value of $K$ is ____.

Moment of inertia (M.I.) of four bodies, having same mass and radius, are reported as ;

I$_1$ = M.I. of thin circular ring about its diameter,
I$_2$ = M.I. of circular disc about an axis perpendicular to disc and going through the centre,
I$_3$ = M.I. of solid cylinder about its axis and
I$_4$ = M.I. of solid sphere about its diameter.

Then :

A football of radius $R$ is kept on a hole of radius $r\ (r < R)$ made on a plank kept horizontally. One end of the plank is now lifted so that it gets tilted making an angle $\theta$ from the horizontal as shown in the figure below. The maximum value of $\theta$ so that the football does not start rolling down the plank satisfies (figure is schematic and not drawn to scale)

A small roller of diameter 20 cm has an axle of diameter 10 cm (see figure below on the left). It is on a horizontal floor and a meter scale is positioned horizontally on its axle with one edge of the scale on top of the axle (see figure on the right). The scale is now pushed slowly on the axle so that it moves without slipping on the axle, and the roller starts rolling without slipping. After the roller has moved 50 cm, the position of the scale will look like (figures are schematic and not drawn to scale)

A circular coil of radius $R$ and $N$ turns has negligible resistance. As shown in the schematic figure, its two ends are connected to two wires and it is hanging by those wires with its plane being vertical. The wires are connected to a capacitor with charge $Q$ through a switch. The coil is in a horizontal uniform magnetic field $B_o$ parallel to the plane of the coil. When the switch is closed, the capacitor gets discharged through the coil in a very short time. By the time the capacitor is discharged fully, magnitude of the angular momentum gained by the coil will be (assume that the discharge time is so short that the coil has hardly rotated during this time)

Put a uniform meter scale horizontally on your extended index fingers with the left one at 0.00 cm and the right one at 90.00 cm. When you attempt to move both the fingers slowly towards the center, initially only the left finger slips with respect to the scale and the right finger does not. After some distance, the left finger stops and the right one starts slipping. Then the right finger stops at a distance $x_R$ from the center (50.00 cm) of the scale and the left one starts slipping again. This happens because of the difference in the frictional forces on the two fingers. If the coefficients of static and dynamic friction between the fingers and the scale are 0.40 and 0.32, respectively, the value of $x_R$ (in cm) is ______.

A rod of mass $m$ and length $L$, pivoted at one of its ends, is hanging vertically. A bullet of the same mass moving at speed $v$ strikes the rod horizontally at a distance $x$ from its pivoted end and gets embedded in it. The combined system now rotates with angular speed $\omega$ about the pivot. The maximum angular speed $\omega_M$ is achieved for $x = x_M$. Then

A thin and uniform rod of mass $M$ and length $L$ is held vertical on a floor with large friction. The rod is released from rest so that it falls by rotating about its contact-point with the floor without slipping. Which of the following statement(s) is/are correct, when the rod makes an angle 60° with vertical?

[$g$ is the acceleration due to gravity]

The potential energy of a particle of mass $m$ at a distance $r$ from a fixed point $O$ is given by $V(r) = kr^2/2$, where $k$ is a positive constant of appropriate dimensions. This particle is moving in a circular orbit of radius $R$ about the point $O$. If $v$ is the speed of the particle and $L$ is the magnitude of its angular momentum about $O$, which of the following statements is (are) true?

Consider a body of mass 1.0 kg at rest at the origin at time $t = 0$. A force $\vec F = (\alpha t\,\hat i + \beta\,\hat j)$ is applied on the body, where $\alpha = 1.0\ \mathrm{N\,s^{-1}}$ and $\beta = 1.0$ N. The torque acting on the body about the origin at time $t = 1.0$ s is $\vec\tau$. Which of the following statements is (are) true?

A ring and a disc are initially at rest, side by side, at the top of an inclined plane which makes an angle 60° with the horizontal. They start to roll without slipping at the same instant of time along the shortest path. If the time difference between their reaching the ground is $(2 - \sqrt3)/\sqrt{10}$ s, then the height of the top of the inclined plane, in metres, is ______. Take $g = 10\ \mathrm{m\,s^{-2}}$.

In the List-I below, four different paths of a particle are given as functions of time. In these functions, $\alpha$ and $\beta$ are positive constants of appropriate dimensions and $\alpha \ne \beta$. In each case, the force acting on the particle is either zero or conservative. In List-II, five physical quantities of the particle are mentioned: $\vec{p}$ is the linear momentum, $\vec{L}$ is the angular momentum about the origin, $K$ is the kinetic energy, $U$ is the potential energy and $E$ is the total energy. Match each path in List-I with those quantities in List-II, which are conserved for that path.

Consider regular polygons with number of sides $n = 3, 4, 5\ldots$ as shown in the figure. The center of mass of all the polygons is at height $h$ from the ground. They roll on a horizontal surface about the leading vertex without slipping and sliding as depicted. The maximum increase in height of the locus of the center of mass for each polygon is $\Delta$. Then $\Delta$ depends on $n$ and $h$ as

A rigid uniform bar AB of length $L$ is slipping from its vertical position on a frictionless floor (as shown in the figure). At some instant of time, the angle made by the bar with the vertical is $\theta$. Which of the following statements about its motion is/are correct?

A wheel of radius $R$ and mass $M$ is placed at the bottom of a fixed step of height $R$ as shown in the figure. A constant force is continuously applied on the surface of the wheel so that it just climbs the step without slipping. Consider the torque $\tau$ about an axis normal to the plane of the paper passing through the point $Q$. Which of the following options is/are correct?

The total kinetic energy of the ring is

The moment of inertia of a uniform cylinder of length $l$ and radius R about its perpendicular bisector is I. What is the ratio $l/R$ such that the moment of inertia is minimum ?

A slender uniform rod of mass M and length $l$ is pivoted at one end so that it can rotate in a vertical plane (see figure). There is negligible friction at the pivot. The free end is held vertically above the pivot and then released. The angular acceleration of the rod when it makes an angle θ with the vertical is :

A uniform disc of radius R and mass M is free to rotate only about its axis. A string is wrapped over its rim and a body of mass m is tied to the free end of the string as shown in the figure. The body is released from rest. Then the acceleration of the body is :